Renewables have been promoted as clean energy without much attention being given to their cost or effectiveness.
This results in an illusory view of renewables, which these two articles address.
The different types of power generation equipment, from coal-powered steam turbines to wind turbines, are assigned nameplate ratings.
The nameplate rating defines the amount of electricity a unit can produce if operated continuously.
One measure of effectiveness is capacity factor.
Capacity factor is a measure of the amount of electricity actually generated by an installation, compared with the theoretical amount that could be generated based on its nameplate rating.
The measurement relates to power generation for the grid. PV solar on roof tops need to be evaluated differently, which was done in the article The Solar-Induced Death Spiral.
The capacity factor of a nuclear power plant is typically 90% or slightly more. This means that an investment in a nuclear power plant can be expected to generate 90% of the electricity that could theoretically be generated based on its nameplate rating.
Wind turbines have a capacity factor of around 30%. This reflects the fact that they don’t generate electricity when the wind isn’t blowing or when the wind blows too hard, say over 55 mph. It also reflects that between the units lowest operating speed, say 5 mph, to its most efficient operating speed, say 35 mph, it operates at different efficiencies. Wind turbines are least efficient at low wind speeds; say 5 mph, with efficiency gradually increasing as wind speed increases, until the wind turbine is operating most efficiently.
The American Wind Energy Association (AWEA) actually misleads the public when it announces that “x” megawatts (MW) of wind turbines have been installed during the year.
Comparing the MW of installed wind turbines with the MW of installed nuclear, coal or NGCC, overstates the amount of electricity that can be produced by wind turbines.
The AWEA compares apples with oranges, and misleads people into thinking that equal investments in MW of wind or NGCC power plants produce equal amounts of electricity.
Capacity factors for major types of power generation installations are:
- Nuclear 90%
- Coal 85%
- Natural Gas Combined Cycle (NGCC) 85%
- Wind 30%
The effect of capacity factor can be seen by making a few calculations.
Typical wind turbines are rated at 1.5 MW.
Because their capacity factor is only 30%, it would take 2,000 wind turbines to generate the same amount of electricity as one 1,000 MW nuclear power plant, or over 1,600 wind turbines to replace one 850 MW natural gas combined cycle (NGCC) power plant.
Wind turbines also have to be spaced far enough apart that the back flow from one turbine doesn’t affect another so that they require around 50 acres per turbine. A 2,000 turbine wind farm, therefore, could require around 100,000 acres.
Wind turbines require considerably more space, with supporting roads and transmission facilities, than do either a single nuclear power plant or a single NGCC power plant.
Concentrating solar power has a capacity factor of around 25%2.
The largest such plant built in the United Sates is the Ivanpah concentrating solar power plant, rated at 377 MW, built in the California desert. The plant required 4,000 acres.
Approximately 9 Ivanpah’s would be required to produce the same amount of electricity as one, 1,000 MW, nuclear power plant, or 8 Ivanpahs would be needed to replace one, 850 MW, NGCC power plant.
Area wise, 9 Ivanpah’s would require 36,000 acres.
Nuclear, coal-fired and NGCC power plants all require less than 1,000 acres.
Similar conclusions can be reached for coal-fired power plants.
It’s evident, therefore, that renewables are not as effective as nuclear, NGCC or coal-fired power plants.
This effectiveness can be translated into costs, which is the subject of the next article.
- Interestingly, the news story from KQED Science, on February 13, 2014, said the Ivanpah plant would provide enough electricity for140,000 homes per year, whereas, the official press release from Brightsource, the developer of Ivanpah, said it would provide enough electricity for 140,000 homes during peak hours. This is an amazing difference that KQED Science, failed to recognize, which misrepresented the facts to the public.
While anyone can make a mistake, it reemphasizes the importance of carefully reading and understanding media reports.
- CSP capacity factor can be increased with 6 hours of thermal storage, and, according to a report by the CSP industry, It is increased to approximately 45%.
* * * * * *
These articles can be delivered directly to your mailbox. Subscribe by clicking below the photo on the right side of the article where it says email subscription, and entering your email address. You can unsubscribe at any time.
If you know someone who would be interested in these articles you can send him/her a link to the article and suggest he/she subscribes by clicking on the email subscription link under the picture on the right side of the page, and entering their email address.
To find earlier articles, click on the name of the preceding month below the calendar to display a list of articles published in that month. Continue clicking on the name of the preceding month to display articles published in prior months.
© Power For USA, 2010 – 2014. Unauthorized use and/or duplication of this material without express and written permission from this blog’s author, Donn Dears, LLC, is strictly prohibited. Excerpts and links may be used, provided that full and clear credit is given to Power For USA with appropriate and specific direction to the original content.